View source for OpenHab

2020-May-07 [[Wink]] announced they are going to a subscription service, so I am migrating to [[OpenHab]]

I bought a [https://www.homedepot.com/p/Wink-Bright-PPBNDL-WNK1/302121348 Wink Bright kit] from Home Depot (6/26/18) and two Cree Zigbee bulbs from Amazon (6/23/18) Later (12/18) I got the outlets.

I have other stuff that was not usable in the Wink system that I have not documented yet.

== Hardware ==
Controller:
* OpenHab running in Docker on [[Bellman]].
* [https://www.nortekcontrol.com/products/2gig/husbzb-1-gocontrol-quickstick-combo/ Nortek HUSBZB-1] to talk Zigbee and ZWave purchased 5/7/20 from Newegg, [https://www.nortekcontrol.com/pdf/manuals/husbzb-1-instructions.pdf spec sheet here]

Controlled: 
* 2 bulbs that came with Wink
* 1 soft white bulb: Cree BA19-08027OMF-12CE26-1C100 Connected 60W Equivalent Soft White 
* 1 daylight bulb: Cree BA19-08050OMF-12CE26-1C100 Connected 60W Equivalent Daylight (5000K)
* 2 two Centralite Mini outlets (from Amazon) to control strings of X-mas lights.

== Set up ==

# Edit docker-compose.yml
# docker-compose up
# https://openhab:8444/ (I moved it up a port becasue UniFi is already running at 8443.)

=== Nortek ===

"HubZ is effectively a USB to UART bridge connected to a [https://www.silabs.com/wireless/zigbee/em35x-zigbee-socs Silicon Labs EM3581 ZigBee module] that allows connectivity to a computer�s USB port."

The Nortek is now plugged in and shows up in lsusb as

 Bus 003 Device 007: ID 10c4:8a2a Cygnal Integrated Products, Inc.

dmesg sees it as 2 serial ports, 
<pre>
[1200065.974054] usb 3-1.2: new full-speed USB device number 7 using ehci-pci
[1200066.085372] usb 3-1.2: New USB device found, idVendor=10c4, idProduct=8a2a, bcdDevice= 1.00
[1200066.085378] usb 3-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[1200066.085382] usb 3-1.2: Product: HubZ Smart Home Controller
[1200066.085385] usb 3-1.2: Manufacturer: Silicon Labs
[1200066.085388] usb 3-1.2: SerialNumber: 81300CEB
[1200066.116633] usbcore: registered new interface driver usbserial_generic
[1200066.116667] usbserial: USB Serial support registered for generic
[1200066.124434] usbcore: registered new interface driver cp210x
[1200066.124471] usbserial: USB Serial support registered for cp210x
[1200066.124540] cp210x 3-1.2:1.0: cp210x converter detected
[1200066.127400] usb 3-1.2: cp210x converter now attached to ttyUSB0
[1200066.127806] cp210x 3-1.2:1.1: cp210x converter detected
[1200066.130746] usb 3-1.2: cp210x converter now attached to ttyUSB1
</pre>

So this means I have to add /dev/ttyUSB0 and /dev/ttyUSB1 and the JAVA OPTS to the docker-compose.yml file and restart it. 
EXTRA_JAVA_OPTS="-Dgnu.io.rxtx.SerialPorts=/dev/ttyUSB0:/dev/ttyUSB1"

* ZWave is on ttyUSB0 (untested)
* Zigbee is on ttyUSB1 using 57600 8N1 software handshake

=== Add "Things" ===

After pairing a new device (or "creating a Thing")
# In Paper UI, 
# Configuration -> Add an item, click the "+".
# Name and create an item to go with the thing, for a bulb, create a dimmer or a switch typically.
# Click "+" to save it.
# Link the item and the thing

=== Cree "Connected" bulbs ===

# To prepare, put the bulb in a fixture with an on/off switch on it.
# Go to paper UI in OpenHab
# Go to Inbox and "Search For Things" and "Zigbee Binding"
# Click "Add manually", now you have about 60 seconds, tick tick...
# Switch Cree OFF for 2 seconds, on for 1 second. Repeat 4 times,
on the fourth try it should start blinking it's reset and unpaired. 
# OpenHab will see it soon.
# Go to Configuration -> Things and you should see it in the list. Change its name if you want.

=== OSRAM "Lightify" A19 bulbs ===

# Click it on and off until it blinks a few times. Then it's reset.
# Switch it on.
# Go to paper UI in OpenHab
# Go to Inbox and "Search For Things" and "Zigbee Binding"
# Click "Add manually", it should find the uninitialized bulb almost immediately.
# Go to Configuration -> Things and you should see it in the list. Change its name if you want.

=== Centralite switches ===
Model 4200-C

'''Reset'''
Unplug any devices from the module and unplug from
the wall. Now hold the on/off button while plugging
it back into the wall. Hold the button until the status
LED turns on. Repeat the �Getting Started� steps to
rejoin the ZigBee network

Now go add a thing and an item like the bulbs; use a SWITCH not a DIMMER.

[[Category: IoT]]