Maker Camp 2015: Difference between revisions
From Wildsong
Jump to navigationJump to search
Brian Wilson (talk | contribs) mNo edit summary |
Brian Wilson (talk | contribs) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 20: | Line 20: | ||
== Maker Camp supplies == | == Maker Camp supplies == | ||
* 1 Arduino Uno | * 1 [[Arduino Uno]], based on the Atmel ATMega328, similar to this [[FutureKit Temperature Controller]] | ||
* 1 16x2 LCD display, LED backlight, parallel interface, TOPWAY LMB162ABC http://topwaydisplay.com/Pub/Manual/LMB162ABC-Manual-Rev0.2.pdf | * 1 16x2 LCD display, LED backlight, parallel interface, TOPWAY LMB162ABC http://topwaydisplay.com/Pub/Manual/LMB162ABC-Manual-Rev0.2.pdf | ||
* 1 3 pin ribbon cable w connectors (for Arduino?) | * 1 3 pin ribbon cable w connectors (for Arduino?) | ||
* 1 74HC86N | * 1 74HC86N quad 2-input XOR gate | ||
* 1 CD4026BE | * 1 CD4026BE decade counter / 7-seg display driver | ||
* 8 2N6027 programmable unijunction transistor | * 8 2N6027 programmable unijunction transistor | ||
* 12 RGB (4 pin) LEDs. | * 12 RGB (4 pin) LEDs. | ||
| Line 36: | Line 36: | ||
* 6 PC mount push buttons | * 6 PC mount push buttons | ||
* 1 2xAA battery holder | * 1 2xAA battery holder | ||
* Coax 2.5 mm power connectors (1 male, 2 female) | * Coax 2.5 mm power connectors (1 male, 2 female) | ||
* 1 9V battery connector | * 1 9V battery connector | ||
| Line 47: | Line 46: | ||
* 2 pager motors | * 2 pager motors | ||
* 1 tiny speaker (or mic?) | * 1 tiny speaker (or mic?) | ||
* 2 pin power cable with pc mount header | * 1 Makershed Albercook Scientific "super cap racer" kit http://makezine.com/2011/12/19/new-in-the-maker-shed-super-cap-racers/ which includes | ||
* 1 5V 0.1F supercap, PowerStore Aerogel | ** 2 pin power cable with pc mount header | ||
* 1 PC mount microswitch | ** 1 5V 0.1F supercap, PowerStore Aerogel | ||
* 1 | ** 1 PC mount microswitch | ||
** 1 3xAAA battery holder | |||
** 1 piece of wire (the tail) | |||
** 2 rubber caps used as tires | |||
Latest revision as of 00:20, 23 July 2015
Crickets thesis paper http://www.kaiser-media.de/thesis/thesis/cover.htm
A different one: http://cricket.csail.mit.edu/ indoor location
Digikey 10F322 processor in DIP package is $.58 in qty 25 2 disposable AAA cells $1.16 for 2
Allelectronics.com
Piezo $.75 self adhesive
cds resistor 1.10
2 AAA battery holder w leads .80
$4.34 total
Maker Camp supplies
- 1 Arduino Uno, based on the Atmel ATMega328, similar to this FutureKit Temperature Controller
- 1 16x2 LCD display, LED backlight, parallel interface, TOPWAY LMB162ABC http://topwaydisplay.com/Pub/Manual/LMB162ABC-Manual-Rev0.2.pdf
- 1 3 pin ribbon cable w connectors (for Arduino?)
- 1 74HC86N quad 2-input XOR gate
- 1 CD4026BE decade counter / 7-seg display driver
- 8 2N6027 programmable unijunction transistor
- 12 RGB (4 pin) LEDs.
- misc LEDs, mostly water clear 5mm. A few others.
- bag of resistors 470K
- 1 Piezo buzzer, TDK
- 2 PC mount relays, small KEST KS2E-M-DC12, 12v input, 125vac/1A contacts
- 1 big toggle switch, panel mount
- 1 3 pin opto device, probably an IR sensor, PC through hole, marked 340
- 1 red push button, panel mount
- 6 PC mount push buttons
- 1 2xAA battery holder
- Coax 2.5 mm power connectors (1 male, 2 female)
- 1 9V battery connector
- 7 alligator clips
- 2 proto boards, 7x9cm BNK
- 1 proto board
- 1 piece of perf board
- 1 DIP chip extractor
- 2 pieces of heat shrink tubing
- 2 pager motors
- 1 tiny speaker (or mic?)
- 1 Makershed Albercook Scientific "super cap racer" kit http://makezine.com/2011/12/19/new-in-the-maker-shed-super-cap-racers/ which includes
- 2 pin power cable with pc mount header
- 1 5V 0.1F supercap, PowerStore Aerogel
- 1 PC mount microswitch
- 1 3xAAA battery holder
- 1 piece of wire (the tail)
- 2 rubber caps used as tires
