Carbon diet
It is called "Mountain top removal"
def: Mountain Top Removal
February 2006
I don't approve of people destroying Appalachia so we can heat our houses with electricity from coal-fired power plants. So I am putting myself on a low carbon diet.
Conservation begins with data collection
I have to establish a baseline of our current energy use. I will need to log electrical use and temperatures over a period of time.
My house uses gas (and optionally, wood) for heat. It has an electric stove and water heater. Only the antique gas/wood central furnace uses gas.
I can monitor its run time by monitoring the electrical circuits running to it. I don't have a good way to measure actual gas used other than gas meter readings. I suppose I could read the meter once a day and log it. For a simple gas-only furnace, one way to measure furnace use is to monitor the fans; when the fans go on, hot air is being pushed through the burner so the burner is running. My furnace complicates things by having both wood and gas sections, so I will have to address that. (Possibly by replacing it!)
I can install a data logger and current taps at the main breaker panel to get readings on the whole house.
Current taps
I happen to have a couple split-core current sensors left over from my halcyon days at Coactive Networks. They are Magnelab Model File:Sct-0750.pdf-100 and they say "100A to .333v Full Range". I bet that means that when 100 amps runs through the cable, it puts out 1/3 volt DC.
From the datasheet, it puts out .066 volts at 20% or 20A in this case.
This is good for whole house. You put one around each cable coming into the breaker panel. 100A is a bit much for other applications though. I would like something in the 15 amp range (one circuit breaker)
You can buy direct from the factory; they are $46 each. If you don't need the split core feature you can get sensors in the $30 range.
Other sources
Digikey Search catalog for Current Transducer or Current Sensor
AC Line Voltage
Data loggers
What do I connect my sensors to? A logger records information which can later be transferred to a desktop computer typically via serial port for analysis. Using a logger to buffer data means you don't have to have your computer turned on all the time to log data in real-time. You can leave it plugged in all the time, and just grab data when the computer is powered on.
| Onset | Hobo | < $100 | sells matched sensors including split core transformers |
| Pace Scientific | Pocket Logger | $499 | expensive but full range of accessories |
Remote locations
This won't work if your sensors are located up the street in another building. How can we move the data over a longer distance?
Dialup modem? Sure. Connect an external modem to the serial port and program it to answer the phone. This is fine if you still use modems :-) and have a phone line available at the remote site.
Network connection or WiFi connection - Well now, this could be where the WRT54GS project comes in handy. For around $60 and a little hacking I can connect a WRT54GS access point to the data logger via RS232 serial port, and it can then act as the bridge to the network via either its 5 ethernet ports or its Wifi port. In fact for this tiny app I could probably also just use one of my old USR2450 WiFi modules. They already have serial ports built in.
Measurements using Kill-a-watt
Computers
HP Vectra desktop
- Astec ATX90-3405 SFX/MicroATX power supply [1]
- HP Motherboard
- RAM
(SFX has no -5V supply so is not ISA compatible. 90W is all the spec requires.)
Via EPIA 800
- Astec ATX90 power supply
Board by itself draws 29W with this supply
Adding the CD drive, draws 3W more when drive checks for CD then drops to 29W
Adding the Vectra HD, draws 34W at boot and then drops to 22W,
so the CPU must still be doing some work when it is unable to boot.
Spinning down the HD drops it to 19W.
What I'd like to do is load up a CF card with the operating system and have the hard drive hold only data, so when the system is idle the drive spins down.
Generic Pentium Pro 200 system
- Powerman 235W ATX supply with on/off switch
- Pentium Pro 200 Intel Mars motherboard
- Four 72 pin 32MB SIMMS = 128 MB
- No CPU fan (power supply fan directs air directly onto heatsink)
- Tulip network card (est 2W)
- Soundblaster Model CT4180 card (2W)
- Dual port Intel network card (3-4W)
- Dual port SIIG USB 1.0 card (2W)
- Trident video card (ISA) (3W)
- Intel Mars motherboard PIIX chipset
- PS/2 keyboard (no difference on power reading w/o keyboard)
- IDE hard drive: IBM Deskstar 15 GB IBM-DTLA-307015
Boot: 55-60W, peaks to 70W
Idle: 36W
HD spun down: 31W
Stripped down: MB + 128MB RAM + HD = 23 W
Spinning down the hard drive saves 5 watts
Power supply has OFF switch; with the various and sundry network cards installed it burns
PS fan and CPU fan died years ago so I put the high quality fan from a Sun 3 workstation into the supply and dumped the CPU fan. CPU does NOT get hot under normal operation.
CDROM drives
Only needed occasionally; I can leave a drive in the system but unhook power to it.
- Diamond 8X CDROM: 1 W when idle (no disc in drive)
Mini-ITX
The system tested above based on the Via board is in the Mini-ITX form factor. There are "fanless" and "fan" versions with 500 and 800 Mhz processors. I currently use an 800 Mhz board with a fanless Zalman BZ-47 Northbridge heatsink and the case / power supply fans provide adequate cooling.
I monitor temperatures and turn down the fans using a controller from Sunbeam.
C7 upgrade
The C3 processor on the Via 800 Mhz card is basically a Pentium instruction set.
The new C7 processor has an advanced instruction set and it's faster. Does this mean it uses more power? Or is it more efficient. I have gotten a CN10000 board from logicsupply.
CPUFreq
Turn the CPU speed down when you aren't using it!
Two options are cpufreqd amd powernowd I am testing powernowd.
I installed powernowd from the Debian package.
For the C3 processor, enabling speed control means loading the 'longhaul' module and one of the governor module. For powernowd, the governor to use is 'userspace'. From the command line,
modprobe longhaul modprobe cpufreq_userspace
Look in /proc/cpuinfo to see the current CPU speed. Right now I see
processor : 0 vendor_id : CentaurHauls cpu family : 6 model : 7 model name : VIA Samuel 2 stepping : 3 cpu MHz : 400.094 cache size : 64 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu de tsc msr cx8 mtrr pge mmx 3dnow bogomips : 800.57
It's cut the CPU speed to 400 Mhz (normally it is 800.) Now I can drive up the load by playing a movie and check again. Sure enough! When the movie plays I see the cpuinfo report
cpu MHz : 800.189
NOW... I need to know more accurately just how much power this baby is using. I need some instrumentation!
Power measurement
I have been using a Kill-A-Watt. This is a quick way to get a power reading at the wall outlet. There is a logging alternative to the Kill-a-watt. There is the Wattnode. Both of these are good options for monitoring at the wall outlet.At this point though, I want to be able to measure internal components too.
- Measure power supply efficiency. (Compare at wall and at power supply outputs)
- Check effectiveness of cpufreq and powernowd.
- Compare power used by different hard drives and other components.
- Compare power use with and without WiFi board installed.
- Figure out how to power down unused components and see if it works.
Ideally I want to be able to measure power over long periods of time, so connecting my trusty Fluke 77 and watching the display is not an option.
Methods of current measurement
Series resistor - put a small resistance in series with the load and measure voltage drop across it. Simple, but wastes lots of power thereby defeating my whole purpose.
SCT - put a current clamp around the wire.
Hall-effect - put a hall effect device next to the wire. Allegro makes some specifically for monitoring current.
The SCT's that I happen to have are in the 100 AMP range, too big for this project. I either need smaller SCT's or a hall effect device.
